How LAN Switches Work ...
In the case of the Internet, all of these pieces work together to allow your computer to send information to another computer that could be on the other side of the world!
Switches are another fundamental part of many networks because they speed things up. Switches allow different nodes (a network connection point, typically a computer) of a network to communicate directly with one another in a smooth and efficient manner.
There are many different types of switches and networks. Switches that provide a separate connection for each node in a company's internal network are called LAN switches.
Essentially, a LAN switch creates a series of instant networks that contain only the two devices communicating with each other at that particular moment.
Networking Basics
Here are some of the fundamental parts of a network
Network - A network is a group of computers connected together in a way that allows information to be exchanged between the computers.
Node - A node is anything that is connected to the network. While a node is typically a computer, it can also be something like a printer or CD-ROM tower.
Segment - A segment is any portion of a network that is separated, by a switch, bridge or router, from other parts of the network.
Backbone - The backbone is the main cabling of a network that all of the segments connect to. Typically, the backbone is capable of carrying more information than the individual segments. For example, each segment may have a transfer rate of 10 Mbps (megabits per second), while the backbone may operate at 100 Mbps.
Topology - Topology is the way that each node is physically connected to the network (more on this in the next section).
Local Area Network (LAN) - A LAN is a network of computers that are in the same general physical location, usually within a building or a campus. If the computers are far apart (such as across town or in different cities), then a Wide Area Network (WAN) is typically used.
Network Interface Card (NIC) - Every computer (and most other devices) is connected to a network through an NIC. In most desktop computers, this is an Ethernet card (normally 10 or 100 Mbps) that is plugged into a slot on the computer's motherboard.
Media Access Control (MAC) address - This is the physical address of any device -- such as the NIC in a computer -- on the network. The MAC address, which is made up of two equal parts, is 6 bytes long. The first 3 bytes identify the company that made the NIC. The second 3 bytes are the serial number of the NIC itself.
Unicast - A unicast is a transmission from one node addressed specifically to another node.
Multicast - In a multicast, a node sends a packet addressed to a special group address. Devices that are interested in this group register to receive packets addressed to the group. An example might be a Cisco router sending out an update to all of the other Cisco routers.
Broadcast - In a broadcast, a node sends out a packet that is intended for transmission to all other nodes on the network
Network Topologies
Some of the most common topologies in use today include:
Bus - Each node is daisy-chained (connected one right after the other) along the same backbone, similar to Christmas lights. Information sent from a node travels along the backbone until it reaches its destination node. Each end of a bus network must be terminated with a resistor to keep the signal that is sent by a node across the network from bouncing back when it reaches the end of the cable.
Ring - Like a bus network, rings have the nodes daisy-chained. The difference is that the end of the network comes back around to the first node, creating a complete circuit. In a ring network, each node takes a turn sending and receiving information through the use of a token. The token, along with any data, is sent from the first node to the second node, which extracts the data addressed to it and adds any data it wishes to send. Then, the second node passes the token and data to the third node, and so on until it comes back around to the first node again. Only the node with the token is allowed to send data. All other nodes must wait for the token to come to them.
Star - In a star network, each node is connected to a central device called a hub. The hub takes a signal that comes from any node and passes it along to all the other nodes in the network. A hub does not perform any type of filtering or routing of the data. It is simply a junction that joins all the different nodes together.
Star bus - Probably the most common network topology in use today, star bus combines elements of the star and bus topologies to create a versatile network environment. Nodes in particular areas are connected to hubs (creating stars), and the hubs are connected together along the network backbone (like a bus network). Quite often, stars are nested within stars, as seen in the example below:
The Problem: Traffic
In the most basic type of network found today, nodes are simply connected together using hubs. As a network grows, there are some potential problems with this configuration:
Scalability - In a hub network, limited shared bandwidth makes it difficult to accommodate significant growth without sacrificing performance. Applications today need more bandwidth than ever before. Quite often, the entire network must be redesigned periodically to accommodate growth.
Latency - This is the amount of time that it takes a packet to get to its destination. Since each node in a hub-based network has to wait for an opportunity to transmit in order to avoid collisions, the latency can increase significantly as you add more nodes. Or, if someone is transmitting a large file across the network, then all of the other nodes have to wait for an opportunity to send their own packets. You have probably seen this before at work -- you try to access a server or the Internet and suddenly everything slows down to a crawl.
Network failure - In a typical network, one device on a hub can cause problems for other devices attached to the hub due to incorrect speed settings (100 Mbps on a 10-Mbps hub) or excessive broadcasts. Switches can be configured to limit broadcast levels.
Collisions - Ethernet uses a process called CSMA/CD (Carrier Sense Multiple Access with Collision Detection) to communicate across the network. Under CSMA/CD, a node will not send out a packet unless the network is clear of traffic. If two nodes send out packets at the same time, a collision occurs and the packets are lost. Then both nodes wait a random amount of time and retransmit the packets. Any part of the network where there is a possibility that packets from two or more nodes will interfere with each other is considered to be part of the same collision domain. A network with a large number of nodes on the same segment will often have a lot of collisions and therefore a large collision domain.
While hubs provide an easy way to scale up and shorten the distance that the packets must travel to get from one node to another, they do not break up the actual network into discrete segments. That is where switches come in. In the next section, you'll find out how switches assist in directing network traffic.
|
|
